This article describes a simple setup of electrospinning using widely available resources. The Arduino board, an electronic platform that is commonly accessible was adapted for a controller. Specifically, recycled parts consisting of plastic gears and a lipstick case were incorporated for the construction of a syringe pump. A cheap DC-DC converter…

An organic solar cell fabrication kit has been developed for demonstration in both undergraduate teaching classes and high school laboratories to promote the growing field of renewable energy and to facilitate empirical comprehension of solar technology. The laboratory focuses on fabricating organic photovoltaics (solar cells) and testing the…

[This paper is part of the Focused Collection on Instructional labs: Improving traditions and new directions.] We present the pedagogical design and implementation of "ESSENCe": Experimental problem solving using Staging, Scaffolding, Embedded information sources, iNstruments, and Collaboration. Research in experimental physics requires…

Many types of batteries power an ever-growing number of devices. Electrochemical devices like batteries and fuel cells can, in principle, exceed Carnot efficiency for energy conversion. In this novel laboratory experiment, students explore the partitioning of the enthalpy change of a battery's electrochemical reaction between useful electrical…

Scanning probe-based microscopes (SPMs) are widely used in biology, chemistry, materials science, and physics to image and manipulate matter on the nanoscale. Unfortunately, high school and university departments lack expensive SPM tools and materials microscopy activities to educate a large number of students in this vital SPM imaging technique.…

A series of hands-on experiments including the synthesis and application of flexible, conductive silver-nanopaste were designed to gain knowledge of conductive soft nanomaterial and the synthesis and the application of silver nanopaste (Ag nanopaste). The aim of this laboratory experiment is to provide undergraduate/graduate students an…

The ability to develop, use, and refine models of experimental systems is a nationally recognized learning outcome for undergraduate physics lab courses. However, no assessments of students' model-based reasoning exist for upper-division labs. This study is the first step toward development of modeling assessments for optics and electronics labs.…

An undergraduate electrical conductivity measurement experiment in a physical chemistry lab and basic fitting procedures are presented that allow a characterization of micellar system of hexadecyltrimethylammonium bromide (cetyltrimethylammonium bromide, CTAB) in binary mixture of water and acetonitrile (ACN) as a cosolvent (10%, v/v) at 30.0 °C.…

The research reported in this article represents a systematic, multiyear investigation of student understanding of the behavior of bipolar junction transistor circuits using a variety of different tasks to isolate and probe key aspects of transistor circuit behavior. The participants in this study were undergraduates enrolled in upper-division…

Acharge pickup detector was developed at the University of Colorado for use in classroom demonstrations and in the dust accelerator at the Institute for Modeling Plasma, Atmospheres and Cosmic Dust (IMPACT). The detector can be used in a physics classroom to help high school and introductory-level physics students connect electromagnetic phenomena…

A student laboratory experiment to investigate the intrinsic and extrinsic bandgaps, dopant materials, and diode design in light-emitting diodes (LEDs) is presented. The LED intrinsic bandgap is determined by passing a small constant current through the diode and recording the junction voltage variation with temperature. A second visible…

The use of the Beer-Lambert law in spectroscopy is the core of standard methods for determining a chromophore concentration in a solution. Its application requires an understanding about interaction of light with a colored solution and the use of light emission and light detection devices. We build here a simple electronic circuit formed of…

The teaching of instrumental analysis for many small colleges and high schools continues to be stymied by high-cost, complicated maintenance, high power requirements, and often the sheer bulk of the instrumentation. Such issues have led us to develop inexpensive instruments as part of a SMILE initiative (small, mobile instruments for laboratory…

A laboratory experiment is described in which students fabricate disk-shaped gold and platinum microelectrodes with diameters of 10-50 [mu]m by sealing sodalime glass with metal microwires. The electrodes are characterized by performing cyclic voltammetry in aqueous and acetonitrile solution. Commercial microelectrodes are expensive (cost depends…

Calculating the effective resistance of an electrical network is a common problem in introductory physics courses. Such calculations are typically restricted to two-dimensional networks, though even such networks can become increasingly complex, leading to several studies on their properties. Furthermore, several authors have used advanced…