The article introduces a low-cost Arduino sensor into the Young's modulus determination laboratory for physics university students. A stainless steel ruler is used as a cantilever beam. Its free end attached a mass is slightly bent and released to make it oscillate as a simple harmonic motion. The Arduino sensor detects the moving mass's frequency…

This study has proposed a simple method to show the convective heat transfer. The object in this study is an air conditioner (AC) as a simple case of convection. In addition, AC is also easy to find in the class because most classrooms in Indonesia installed AC. Usually, a visualization needs special software (i.e. MatLab or others) and good…

This paper describes the development of a light polarization experimental apparatus for a remote laboratory. The apparatus had been developed by controlling the analyzer rotation using a stepper motor controlled via the Arduino. Device control and data acquisition applications were developed with LabVIEW which provides remote control panel…

Electroscopes have been widely used in physics education for several reasons, such as their simplicity, sensitivity and visual appeal, showing macroscopic phenomena related to the microscopic world. Although they are capable of highly accurate measurements, the procedures involved in these measurements encounter some obstacles when performed with…

Teaching alternating currents, ac or sound waves, is incomplete without an introduction to the oscilloscope. An oscilloscope is a tool that graphically displays electrical signals and shows their time dependence. However, due to the pandemic, triggered by the SARS-CoV-2 virus, many students do not have the opportunity to master the use of an…

The image of free-falling bar has been recorded to study the effect of the motion on its observed length. This moving bar image is analysed using the Tracker software to determine its length and the end bar's position. An elongated appearance of the bar has been observed with movement. This effect relies on the speed and the exposure time during…

Granular flows appear frequently in the natural world and in civil engineering applications. These flows can exhibit features which are surprising and counter-intuitive and are often used to test the limits of the classical continuum approximation for modelling of fluid flows. An important sub-class of the granular flows are the gravity-driven…

The experiment in charging and discharging of a capacitor through a resistor is fundamentally important for studying electronics. We have developed an alternative procedure to measure the voltage drops across capacitors as a function of time. The simple apparatus controlled by an Arduino Uno microcontroller board and LabVIEW™ interface was set up.…

Light spectrum dispersion is an exciting subject in science because of its beautiful atmospheric colour phenomenon which attracts students. However, to see the phenomenon is not easy since it needs a spectrometer, which is commonly expensive. Therefore, the present study aims to describe a low-cost spectrometer for investigating lighting spectrum…

A simple measurement of the refractive index of a liquid has been performed using a spherical lens. This lens is a spherical shape flask containing the liquid under study. Parallel pointer laser beams are directed to the lens to obtain the back focal length of the lens. The focal point is determined visually or using the Tracker software to…

The first of the two postulates of relativity states that the laws of physics are the same in all inertial reference frames. Often it is assumed that the postulates are mainly concerned with objects moving at a significant fraction of the speed of light. However, the postulates are applicable at all speeds from a snail to a photon. To practically…

In this article, we propose a simple and accessible model of a magnetic levitator fitted with a Hall sensor. This model also allows to determine the magnitude of the magnetic field within the levitator working volume. Students can also compare the experimental magnetic field values to reference values in magnetism textbooks. This Arduino-based…

In conventional e/m experiments performed in undergraduate laboratories, generally a simple mechanical ruler is used to measure the radius of the circular trajectory of the electrons. But, the measurement error in this technique is mostly big and varies from one student to another. As an alternative to a mechanical ruler, we proposed a more…

Using a joystick module, we followed the movement of a chaotic magnetic pendulum. The pendulum bar was attached to a joystick that served as a pivot point and biaxial angular motion sensor. Using an Arduino board, we could follow the position as a function of time along both the "x" and "y"-axis and draw a graph showing the…

Students' understanding of forces in circular motion is often incomplete. The problems are not limited to confusions about centripetal acceleration and centrifugal forces. This paper considers possible effects of different interventions by a teacher who has discovered the many types of free-body diagrams drawn by students for circular motion in a…